| |
|
DDA 7 Zi Series
Based on the WavePro 7 Zi Series models, the DDA 7 Zi Series Disk Drive Analyzers are available in 3.5 and 6 GHz models and come equipped with 20 Mpts/ch acquisition memory. Dedicated disk drive measurements, trigger and zooming for failure analysis, and serial data measurement capability with a Disk Drive Analyzer user interface are also standard to address high capacity disk drive designs. Operate in either DDA or SDA mode to analyze the serial data links or the physical media behavior on a hard drive.
- Zoom on multi-zoom on sectors
- One button access to read channel emulation, servo analysis, and disk drive triggers
- Head equalization, channel Emulation, and SAM histograms
- Segmented memory for sector by sector parametric analysis
A Total Solution for Disk Drive Analysis
Maximum Performance
LeCroy Disk Drive Analyzers (DDA) assist data storage design engineers by integrating tools that improve the time to market of new products and accelerate understanding and failure analysis on existing drives. LeCroy continues that tradition with the DDA 7 Zi Series equipped with its powerful Disk Drive Analysis toolset. Capture, view, and analyze the wave shape of high-speed, complex drive signals with speed and integrity.
Data Storage applications are memory intensive as capturing multiple sectors or a complete track of data can be important in troubleshooting a design or characterizing media.
The X-Stream II architecture enables fast and accurate measurements and analysis of disk drive signals. Memory can be extended to 128 Mpts/Ch (256 Mpts/Ch on 2 Ch) using Option L. Both the DDA 760Zi and DDA 735Zi offer the convenience of selectable 50 Ω or 1 MΩ inputs. The standard 20 Mpts of waveform memory and 40 GS/s capture on two channels, means multiple drive sectors can be acquired at once.
Long Memory and Flexibility in Finding Problems
Acquire a head signal up to 6 GHz, and then QuickZoom it from the front panel. The DDA copies and expands the drive signal automatically. Simply scroll horizontally and vertically to examine any sector. Multiple zooms let you view up to eight separate areas of the head signal; each zoom comes in a distinct color. Disk drive parameters let you characterize the pulse width variation or signal-to-noise ratio across a region. Failure Analysis engineers can store and recall golden waveforms and panel setups to compare problem drives with the known good drives. Analog-to-digital converters running at speeds up to 40 GS/s ensure the right sensitivity to measure today’s high-speed read channels. In every DDA, you can run your customer-developed scripts to view the captured signal with the filters matched to your channel and media. Custom user scripts can be created in MATLAB, Visual Basic, Excel or other formats.
Exceptional Trigger and Sequence Performance
The DDA’s disk triggers allow you to set up a series of events in the signal that then cause a trigger. For example, qualify the signal on the index signal and then capture all the sectors of information on the track. As memory is increased in the DDA, more sectors can be captured, with up to 50 picosecond/sample time resolution. Up to 15,000 sectors of data can be gathered with the DDA 7 Zi analyzers. An optional capability, Streaming Sequence, uses the X-Stream II and the fast hardware architecture of the DDA to streamup to 300,000 segments of data to memory; all taken at a high trigger rate.
Natural Graphical Interface
One press on the DDA menu takes you directly to the Disk Drive Analyzer features. The familiar controls on the front panel, coupled with a natural, context-sensitive graphical user-interface, react quickly to your commands. Functionality is exactly where you expect it to be.
The DDA 7 Zi provides one button access to all the tools needed to accurately debug and analyze disk drive operation.
The DDA 7 Zi features:
- 31 custom parameters
- 4 specific drive trigger
- Sector
- Servo Gate
- PES trigger
- Read Gate Trigger
- Advanced drive analysis tools
Advanced Disk Drive analysis tools capabilities include:
- Head Filter Equalizer emulation
- Channel Emulation
- SAM Histograms
- Plot of SAM values
- PES runout analysis
- Analog Compare
Simultaneously connecting low-speed signals, like index and servo gate, and high-speed signals, like read channels has never been easier. With integrated 50 Ω and 1 MΩ inputs on all models, there is no longer a need for expensive adapters.
DDA 735Zi
Analog Bandwidth @ 50 Ω (-3 dB)
|
|
3.5 GHz
|
Rise Time (typical)
|
|
120 ps
|
Input Channels
|
|
4
|
Bandwidth Limiters
|
|
20 MHz, 200 MHz
|
Input Impedance
|
|
50 Ω or 1 MΩ||15pF, 10 MΩ || 11 pF with supplied Probe
|
Input Coupling
|
|
1 MΩ: AC, DC, GND; 50 Ω: DC, GND
|
Maximum Input Voltage
|
|
50 Ω: ±5 Vrms
|
Vertical Resolution
|
|
8 bits; up to 11 bits with enhanced resolution (ERES)
|
Sensitivity
|
|
50 O: 2 mV–1 V/div, fully variable (2-9.99 mV/div via zoom); 1 MO: 2 mV–10 V/div, fully variable
|
DC Gain Accuracy
|
|
±1.5% of full scale
|
Offset Range
|
|
50 Ω:
|
Offset Accuracy
|
|
±(1.5% of full scale + 1.0% of offset value + 1 mV)
|
Timebases
|
|
Internal timebase common to 4 input channels; an external clock may be applied at the auxiliary input
|
Time/Division Range
|
|
20 ps/div–1000 s/div (RIS mode: 20 ps/div - 10 ns/div; Roll mode: up to 1000 s/div)
|
Clock Accuracy
|
|
< 1 ppm
|
Jitter Noise Floor
|
|
800 fs (typical)
|
Trigger and Interpolator Jitter
|
|
2 psrms (typical)
|
Sample Rate and Delay Time Accuracy
|
|
< 0.06 / SR + (1 ppm * Reading) (rms)
|
Channel-Channel Deskew Range
|
|
±9 x time/div. setting, 100 ms max., each channel
|
External Timebase Reference (Input)
|
|
10 MHz; 50 Ω impedance, applied at the rear input
|
External Timebase Reference (Output)
|
|
10 MHz; 50 Ω impedance, output at the rear
|
External Sample Clock
|
|
0.1 Hz-100 MHz, 50 Ω or 1 MΩ impedance, applied at the auxiliary input
|
Single-Shot Sample Rate/Ch
|
|
40 GS/s on 2 Ch
|
Random Interleaved Sampling (RIS)
|
|
200 GS/s for repetitive signals (20 ps/div to 10 ns/div)
|
Maximum Trigger Rate
|
|
1,250,000 waveforms/s (in Sequence Mode, up to 4 channels)
|
Intersegment Time
|
|
800 ns
|
Standard Memory (4 Ch / 2 Ch) (Number of Segments)
|
|
10 M / 20 M
|
S - Memory Option
|
|
32 M / 64 M
|
M - Memory Option
|
|
64 M / 128 M
|
L - Memory Option
|
|
128 M / 256 M
|
Averaging
|
|
Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
|
Enhanced Resolution (ERES)
|
|
From 8.5 to 11 bits vertical resolution
|
Envelope (Extrema)
|
|
Envelope, floor, or roof for up to 1 million sweeps
|
Interpolation
|
|
Linear or Sin x/x
|
Modes
|
|
Normal, Auto, Single, and Stop
|
Sources
|
|
Any input channel, Aux, Aux/10, or line; slope and level unique to each source (except line trigger)
|
Coupling Mode
|
|
DC, AC, HFRej, LFRej
|
Pre-trigger Delay
|
|
0–100% of memory size (adjustable in 1% increments of 100 ns)
|
Post-trigger Delay
|
|
0–10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
|
Hold-off by Time or Events
|
|
From 2 ns up to 20 s or from 1 to 99,999,999 events
|
Internal Trigger Range
|
|
±5 div from center
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProBus Inputs
|
|
2 div @ < 3.5 GHz
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProLink Inputs
|
|
Not Applicable
|
External Trigger Sensitivity
|
|
2 div @ < 1 GHz
|
External Trigger Input Range
|
|
Aux (±0.4 V); Aux/10 (±4 V)
|
Max. Trigger Frequency, SMART Trigger
|
|
2.0 GHz @ = 10 mV/div (minimum signal width setting 250 ps)
|
Edge/ Slope/ Line
|
|
Triggers when signal meets slope (positive, negative, or either) and level condition.
|
TV-Composite Video
|
|
Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative).
|
State or Edge Qualified
|
|
Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events.
|
Dropout
|
|
Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
|
Pattern
|
|
Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
|
Glitch
|
|
Triggers on positive or negative glitches with widths selectable as low as 200ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Width (Signal or Pattern)
|
|
Triggers on positive or negative widths with widths selectable as low as 200ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Interval (Signal or Pattern)
|
|
Triggers on intervals selectable between 1 ns and 20 s.
|
Timeout (State/Edge Qualified)
|
|
Triggers on any source if a given state (or transition edge) has occurred on another source.
|
Runt
|
|
Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
|
Slew Rate
|
|
Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
|
"A" Trigger List
|
|
Edge, Window, Width, Glitch, Pattern, Pattern State, State, Dropout, Interval, Runt, Slew Rate, Serial Data (optional I2C, SPI, UART/RS-232, CAN, LIN, FlexRay)
|
"B" Trigger List
|
|
Edge
|
Exclusion Triggering
|
|
Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
|
Holdoff Between Sequential Triggers
|
|
Arming = Serial & Triggering = Anything, then min. time between events defined by serial pattern length
|
Data Rates
|
|
50 Mb/s - 1.25 Gb/s
|
Pattern Length
|
|
80 bits, NRZ or 8b10b
|
Clock and Data Outputs
|
|
400mVp-p (typical) AC coupled
|
Clock Recovery Jitter
|
|
1 ps rms + 0.3% Unit Interval rms for PRBS data patterns with 50% transition density
|
Clock Recovery Tracking/ Acquisition Range
|
|
50 Mb/s - 1.25 Gb/s
|
Hardware Clock Recovery Loop BW
|
|
PLL Loop BW = Fbaud/5500, 50 Mb/s to 1.25 Gb/s (typical)
|
Optionally available
|
|
I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN, LIN, FlexRay
|
Intensity
|
|
256 Intensity Levels, 1–100% adjustable via front panel control
|
Number of Channels
|
|
up to 4 simultaneously
|
Max Sampling Rate
|
|
40 GS/s (20 GS/s for WavePro 710Zi without WPZi-1GHZ-4X20GS option)
|
Waveforms
|
|
up to 2500 Waveforms/ second
|
Auto Setup
|
|
Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
|
Find Vertical Scale
|
|
Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
|
Probes
|
|
Qty. (4) ÷10 Passive Probes
|
Probe System: ProBus
|
|
Probus (and ProLink on 4-6 GHz models). Automatically detects and supports a variety of compatible probes
|
Scale Factors
|
|
Automatically or manually selected depending on probe used
|
Calibration Output
|
|
1kHz square wave, 1Vp-p (typical), output to probe hook
|
Type
|
|
Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
|
Resolution
|
|
WXGA; 1280 x 768 pixels
|
Number of traces
|
|
Display a maximum of 8 traces. Simultaneously display channel, zoom, memory and math traces.
|
Grid Styles
|
|
Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y
|
Waveform Representation
|
|
Sample dots joined, or sample dots only
|
Analog and Color-Graded Persistence
|
|
Variable saturation levels; stores each trace’s persistence data in memory
|
Trace Selection
|
|
Activate persistence on all or any combination of traces
|
Sweep Display Modes
|
|
All accumulated, or all accumulated with last trace highlighted
|
Persistence Types
|
|
Select analog, color, or three-dimensional
|
Persistence Aging
|
|
Select from 500 ms to infinity
|
Front Panel and Instrument Status
|
|
Store to the internal hard drive or to a USB-connected peripheral device.
|
Type
|
|
LeCroy LSIB
|
Transfer Rate
|
|
500 Mpt/s
|
Output Protocol
|
|
PCI Express, Gen 1 (4 lanes utilized for data transfer)
|
Control Protocol
|
|
TCP/IP
|
Command Set
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
Type
|
|
Intel® CoreTM 2 Quad, 2.5 GHz (or better)
|
Processor Memory
|
|
2 GB standard, up to 8 GB optional
|
Operating System
|
|
Microsoft Windows® Vista Business Edition (64-bit) with SP1
|
Oscilloscope Operating Software
|
|
Entire instrument including any installed optional applications packages operates within a single (X-Stream) Windows application
|
Real Time Clock
|
|
Date and time displayed with waveform an in hardcopy files. SNTP support to synchronize to precision internal clocks.
|
Zoom Expansion Traces
|
|
Display up to 4 Zoom and 8 Math/Zoom traces
|
Internal Waveform Memory
|
|
4 active waveform memory traces (M1-M4) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
|
Remote Control
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
GPIB Port
|
|
Supports IEEE – 488.2
|
LSIB Port (optional)
|
|
Supports PCIe Gen1 x4 protocol with LeCroy supplied API
|
USB Device Port (optional)
|
|
Type-B
|
Ethernet Port
|
|
Supports 10/100/1000 BaseT Ethernet interface (RJ45 port)
|
USB Ports
|
|
minimum 6 total (incl. 3 front panel) USB 2.0 ports support Windows compatible devices
|
External Monitor Port
|
|
15 pin D-Type WXGA compatible to support customer-supplied external monitor.
|
Serial Port
|
|
2 standard
|
Peripheral Bus
|
|
LeCroy LBUS standard
|
Signal Types
|
|
Select External Trigger or External Clock Input on the front panel
|
Coupling
|
|
50 Ω: DC; 1 MΩ: AC, DC, GND
|
Max. Input Voltage
|
|
50 Ω: 5 Vrms; 1 MΩ: 250 V (Peak AC < 10 kHz + DC)
|
Signal Types
|
|
Select from calibrator, control signals or Off
|
Calibrator Signal
|
|
5 Hz–5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0–1 V into 1 MΩ)
|
Control Signals
|
|
Trigger enabled, trigger out, pass/fail status
|
Auto Calibration
|
|
Ensures specified DC and timing accuracy is maintained for 1 year minimum.
|
Voltage
|
|
100–240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection
|
Max. Power Consumption
|
|
850 W/850 VA
|
Temperature (Operating)
|
|
+5 °C to +40 °C including CD-RW/DVD-ROM drive
|
Temperature (Non-Operating)
|
|
–20 °C to +60 °C
|
Humidity (Operating)
|
|
5% to 80% relative humidity (non-condensing) up to +31 °C.
|
Humidity (Non-Operating)
|
|
5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
|
Altitude (Operating)
|
|
Up to 10,000 ft. (3048 m) at or below +25 °C
|
Altitude (Non-Operating)
|
|
Up to 40,000 ft. (12,192 m)
|
Random Vibration (Operating)
|
|
0.5 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
|
Random Vibration (Non-Operating)
|
|
2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
|
Functional Shock
|
|
20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
|
Dimensions (HWD)
|
|
14"H x 18.4"W x 11.4"D (355 x 467 x 289 mm)
|
Weight
|
|
39.5 lbs. (18 kg)
|
Shipping Weight
|
|
57.5 lbs. (26 kg)
|
Certifications
|
|
CE Compliant, UL and cUL listed; conforms to EN 61326, EN 61010-1, UL 61010-1 2nd edition, and CSA C22.2 No. 61010-1-04
|
Warranty and Service
|
|
3-year warranty; calibration recommended annually.
|
DDA 760Zi
Analog Bandwidth @ 50 Ω (-3 dB)
|
|
6 GHz
|
Rise Time (typical)
|
|
70 ps
|
Input Channels
|
|
4
|
Bandwidth Limiters
|
|
20 MHz, 200 MHz
|
Input Impedance
|
|
50 Ω or 1 MΩ||15pF, 10 MΩ || 11 pF with supplied Probe
|
Input Coupling
|
|
1 MΩ: AC, DC, GND; 50 Ω: DC, GND
|
Maximum Input Voltage
|
|
50 Ω (ProBus): ±5 Vrms
|
Vertical Resolution
|
|
8 bits; up to 11 bits with enhanced resolution (ERES)
|
Sensitivity
|
|
50 Ω: 2 mV–1 V/div, fully variable (2-9.99 mV/div via zoom); 1 MΩ: 2 mV–10 V/div, fully variable
|
DC Gain Accuracy
|
|
±1.5% of full scale
|
Offset Range
|
|
50 Ω:
|
Offset Accuracy
|
|
±(1.5% of full scale + 1.0% of offset value + 1 mV)
|
Timebases
|
|
Internal timebase common to 4 input channels; an external clock may be applied at the auxiliary input
|
Time/Division Range
|
|
20 ps/div–1000 s/div (RIS mode: 20 ps/div - 10 ns/div; Roll mode: up to 1000 s/div)
|
Clock Accuracy
|
|
< 1 ppm
|
Jitter Noise Floor
|
|
560 fs (typical)
|
Trigger and Interpolator Jitter
|
|
1 psrms (typical)
|
Sample Rate and Delay Time Accuracy
|
|
< 0.06 / SR + (1 ppm * Reading) (rms)
|
Channel-Channel Deskew Range
|
|
±9 x time/div. setting, 100 ms max., each channel
|
External Timebase Reference (Input)
|
|
10 MHz; 50 Ω impedance, applied at the rear input
|
External Timebase Reference (Output)
|
|
10 MHz; 50 Ω impedance, output at the rear
|
External Sample Clock
|
|
0.1 Hz-100 MHz, 50 Ω or 1 MΩ impedance, applied at the auxiliary input
|
Single-Shot Sample Rate/Ch
|
|
40 GS/s on 2 Ch
|
Random Interleaved Sampling (RIS)
|
|
200 GS/s for repetitive signals (20 ps/div to 10 ns/div)
|
Maximum Trigger Rate
|
|
1,250,000 waveforms/s (in Sequence Mode, up to 4 channels)
|
Intersegment Time
|
|
800 ns
|
Standard Memory (4 Ch / 2 Ch) (Number of Segments)
|
|
10 M / 20 M
|
S - Memory Option
|
|
32 M / 64 M
|
M - Memory Option
|
|
64 M / 128 M
|
L - Memory Option
|
|
128 M / 256 M
|
Averaging
|
|
Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
|
Enhanced Resolution (ERES)
|
|
From 8.5 to 11 bits vertical resolution
|
Envelope (Extrema)
|
|
Envelope, floor, or roof for up to 1 million sweeps
|
Interpolation
|
|
Linear or Sin x/x
|
Modes
|
|
Normal, Auto, Single, and Stop
|
Sources
|
|
Any input channel, Aux, Aux/10, or line; slope and level unique to each source (except line trigger)
|
Coupling Mode
|
|
DC, AC, HFRej, LFRej
|
Pre-trigger Delay
|
|
0–100% of memory size (adjustable in 1% increments of 100 ns)
|
Post-trigger Delay
|
|
0–10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
|
Hold-off by Time or Events
|
|
From 2 ns up to 20 s or from 1 to 99,999,999 events
|
Internal Trigger Range
|
|
±5 div from center
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProBus Inputs
|
|
2 div @ < 3.5 GHz
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProLink Inputs
|
|
2 div @ < 6 GHz
|
External Trigger Sensitivity
|
|
2 div @ < 1 GHz
|
External Trigger Input Range
|
|
Aux (±0.4 V); Aux/10 (±4 V)
|
Max. Trigger Frequency, SMART Trigger
|
|
2.0 GHz @ = 10 mV/div
|
Edge/ Slope/ Line
|
|
Triggers when signal meets slope (positive, negative, or either) and level condition.
|
TV-Composite Video
|
|
Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative).
|
State or Edge Qualified
|
|
Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events.
|
Dropout
|
|
Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
|
Pattern
|
|
Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
|
Glitch
|
|
Triggers on positive or negative glitches with widths selectable as low as 200ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Width (Signal or Pattern)
|
|
Triggers on positive or negative widths with widths selectable as low as 200ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Interval (Signal or Pattern)
|
|
Triggers on intervals selectable between 1 ns and 20 s.
|
Timeout (State/Edge Qualified)
|
|
Triggers on any source if a given state (or transition edge) has occurred on another source.
|
Runt
|
|
Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
|
Slew Rate
|
|
Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
|
"A" Trigger List
|
|
Edge, Window, Width, Glitch, Pattern, Pattern State, State, Dropout, Interval, Runt, Slew Rate, Serial Data (optional I2C, SPI, UART/RS-232, CAN, LIN, FlexRay)
|
"B" Trigger List
|
|
Edge
|
Exclusion Triggering
|
|
Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
|
Holdoff Between Sequential Triggers
|
|
Arming = Serial & Triggering = Anything, then min. time between events defined by serial pattern length
|
Data Rates
|
|
50 Mb/s - 3.125 Gb/s
|
Pattern Length
|
|
80 bits, NRZ or 8b10b
|
Clock and Data Outputs
|
|
400mVp-p (typical) AC coupled
|
Clock Recovery Jitter
|
|
1 ps rms + 0.3% Unit Interval rms for PRBS data patterns with 50% transition density
|
Clock Recovery Tracking/ Acquisition Range
|
|
50 Mb/s - 2.7 Gb/s
|
Hardware Clock Recovery Loop BW
|
|
PLL Loop BW = Fbaud/5500, 50 Mb/s to 1.25 Gb/s (typical)
|
Optionally available
|
|
I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN, LIN, FlexRay
|
Intensity
|
|
256 Intensity Levels, 1–100% adjustable via front panel control
|
Number of Channels
|
|
up to 4 simultaneously
|
Max Sampling Rate
|
|
40 GS/s (20 GS/s for WavePro 710Zi without WPZi-1GHZ-4X20GS option)
|
Waveforms
|
|
up to 2500 Waveforms/ second
|
Auto Setup
|
|
Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
|
Find Vertical Scale
|
|
Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
|
Probes
|
|
Qty. (4) ÷10 Passive Probes
|
Probe System: ProBus
|
|
Probus (and ProLink on 4-6 GHz models). Automatically detects and supports a variety of compatible probes
|
Scale Factors
|
|
Automatically or manually selected depending on probe used
|
Calibration Output
|
|
1kHz square wave, 1Vp-p (typical), output to probe hook
|
Type
|
|
Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
|
Resolution
|
|
WXGA; 1280 x 768 pixels
|
Number of traces
|
|
Display a maximum of 8 traces. Simultaneously display channel, zoom, memory and math traces.
|
Grid Styles
|
|
Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y
|
Waveform Representation
|
|
Sample dots joined, or sample dots only
|
Analog and Color-Graded Persistence
|
|
Variable saturation levels; stores each trace’s persistence data in memory
|
Trace Selection
|
|
Activate persistence on all or any combination of traces
|
Sweep Display Modes
|
|
All accumulated, or all accumulated with last trace highlighted
|
Persistence Types
|
|
Select analog, color, or three-dimensional
|
Persistence Aging
|
|
Select from 500 ms to infinity
|
Front Panel and Instrument Status
|
|
Store to the internal hard drive or to a USB-connected peripheral device.
|
Type
|
|
LeCroy LSIB
|
Transfer Rate
|
|
500 Mpt/s
|
Output Protocol
|
|
PCI Express, Gen 1 (4 lanes utilized for data transfer)
|
Control Protocol
|
|
TCP/IP
|
Command Set
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
Type
|
|
Intel® CoreTM 2 Quad, 2.5 GHz (or better)
|
Processor Memory
|
|
2 GB standard, up to 8 GB optional
|
Operating System
|
|
Microsoft Windows® Vista Business Edition (64-bit) with SP1
|
Oscilloscope Operating Software
|
|
Entire instrument including any installed optional applications packages operates within a single (X-Stream) Windows application
|
Real Time Clock
|
|
Date and time displayed with waveform an in hardcopy files. SNTP support to synchronize to precision internal clocks.
|
Zoom Expansion Traces
|
|
Display up to 4 Zoom and 8 Math/Zoom traces
|
Internal Waveform Memory
|
|
4 active waveform memory traces (M1-M4) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
|
Remote Control
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
GPIB Port
|
|
Supports IEEE – 488.2
|
LSIB Port (optional)
|
|
Supports PCIe Gen1 x4 protocol with LeCroy supplied API
|
USB Device Port (optional)
|
|
Type-B
|
Ethernet Port
|
|
Supports 10/100/1000 BaseT Ethernet interface (RJ45 port)
|
USB Ports
|
|
minimum 6 total (incl. 3 front panel) USB 2.0 ports support Windows compatible devices
|
External Monitor Port
|
|
15 pin D-Type WXGA compatible to support customer-supplied external monitor.
|
Serial Port
|
|
2 standard
|
Peripheral Bus
|
|
LeCroy LBUS standard
|
Signal Types
|
|
Select External Trigger or External Clock Input on the front panel
|
Coupling
|
|
50 Ω: DC; 1 MO: AC, DC, GND
|
Max. Input Voltage
|
|
50 Ω: 5 Vrms; 1 MO: 250 V (Peak AC < 10 kHz + DC)
|
Signal Types
|
|
Select from calibrator, control signals or Off
|
Calibrator Signal
|
|
5 Hz–5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0–1 V into 1 MΩ)
|
Control Signals
|
|
Trigger enabled, trigger out, pass/fail status
|
Auto Calibration
|
|
Ensures specified DC and timing accuracy is maintained for 1 year minimum.
|
Voltage
|
|
100–240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection
|
Max. Power Consumption
|
|
850 W/850 VA
|
Temperature (Operating)
|
|
+5 °C to +40 °C including CD-RW/DVD-ROM drive
|
Temperature (Non-Operating)
|
|
–20 °C to +60 °C
|
Humidity (Operating)
|
|
5% to 80% relative humidity (non-condensing) up to +31 °C.
|
Humidity (Non-Operating)
|
|
5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
|
Altitude (Operating)
|
|
Up to 10,000 ft. (3048 m) at or below +25 °C
|
Altitude (Non-Operating)
|
|
Up to 40,000 ft. (12,192 m)
|
Random Vibration (Operating)
|
|
0.5 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
|
Random Vibration (Non-Operating)
|
|
2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
|
Functional Shock
|
|
20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
|
Dimensions (HWD)
|
|
14"H x 18.4"W x 11.4"D (355 x 467 x 289 mm)
|
Weight
|
|
39.5 lbs. (18 kg)
|
Shipping Weight
|
|
57.5 lbs. (26 kg)
|
Certifications
|
|
CE Compliant, UL and cUL listed; conforms to EN 61326, EN 61010-1, UL 61010-1 2nd edition, and CSA C22.2 No. 61010-1-04
|
Warranty and Service
|
|
3-year warranty; calibration recommended annually.
|
Memory Options
| | DDAZi-L-128 | 128 Mpt/Ch (256 Mpt/Ch Interleaved) Memory Option for DDA Zi. Includes an additional 4 GB of RAM (8 GB total) | | DDAZi-M-64 | 64 Mpt/Ch (128 Mpt/Ch Interleaved) Memory Option for DDA Zi. Includes an additional 4 GB of RAM (8 GB total) | | DDAZi-S-32 | 32 Mpt/Ch (64 Mpt/Ch Interleaved) Memory Option for DDA Zi. Includes an additional 2 GB of RAM (4 GB total) | Serial Trigger and Decode
| | WPZi-FlexrayBus TD | FlexRay Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | | WPZi-FlexRayBus TDP | FlexRay Bus Trigger, Decode, and Physical Layer Test Option for WavePro Zi Series Oscilloscopes | | WPZi-HSPT | 50 Mb/s to 3.125 Gb/s High Speed Serial Trigger Option for 4-6 GHz Oscilloscopes & Disk Drive Analyzers | | WPZi-I2Cbus TD | I2C Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | | WPZi-LINbus TD | LIN Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | | WPZi-MSPT | 50 Mb/s to 1.25 Gb/s Medium Speed Serial Trigger Option for 2.5-3.5 GHz Oscilloscopes & Disk Drive |
|
